Guitar / Bass

Bass Guitar

Get Adobe Reader Cab Design Spec Sheet

Legend CA1059

A larger magnet version of the popular Legend CA10, the Legend CA1059 is a 10” cast-frame bass guitar speaker modeled after the original OEM spec with the punch and clarity that defined the sound of many popular Eden cabinets throughout the decades. Like the CA10, the CA1059’s chassis is truncated on the sides for tight fitting in 2x, 4x, and 8x10 configurations. Along with higher Xmax, the CA1059 also features a larger 59 oz. ferrite magnet, producing higher efficiency, and lower Qts for dampening than its smaller magnet version.

Suggested Retail  $139.99
Your Price  $119.99

For contiguous USA shipments only.

  • Free Shipping
  • Free Tech Support
  • 7-Year Warranty*
*Warranty policy may vary outside the USA.
This table charts the specifications for the Legend CA1059 speaker
Speaker Detail
Specification
Nominal Basket Diameter10", 254 mm
Nominal Impedance*8 Ω
Power Rating*
Program Power500 W
Watts250 W
Resonance48 Hz
Usable Frequency Range50 Hz - 3.2 kHz
Sensitivity*98.7 dB
Magnet Weight59 oz.
Gap Height0.313", 7.95 mm
Voice Coil Diameter2", 51 mm
Thiele & Small Parameters
Resonant Frequency (fs)48 Hz
DC Resistance (Re)5.53 Ω
Coil Inductance (Le)0.11m H
Mechanical Q (Qms)3.27
Electromagnetic Q (Qes)0.28
Total Q (Qts)0.26
Compliance Equivalent Volume (Vas)71.47 liters / 2.52 cu.ft.
Peak Diaphragm Displacement Volume (Vd)165.25 cc
Mechanical Compliance of Suspension (Cms)0.42 mm/N
BL Product (BL)12.54 T-M
Diaphragm Mass Inc. Airload (MMs)27 grams
Efficiency Bandwidth Product (EBP)169
Maximum Linear Excursion (Xmax)4.72 mm
Surface Area of Cone (Sd)350.1 cm2
Maximum Mechanical Limit (Xlim)8.0 mm
Mounting Information
Recommended Enclosure Volume
Sealed N/a
Vented 18.82-70.79 liters / 0.70-2.5 cu.ft.
Driver Volume Displaced0.061 cu.ft. / 1.72 liters
Major Diameter10.5", 266.7 mm
Flat to Flat Diameter10.14", 257.6 mm
Baffle Hole Diameter9.01", 228.9 mm
Front Sealing GasketYes
Rear Sealing GasketYes
Mounting Holes Diameter0.3", 7.6mm
Mounting Holes B.C.D.9.71", 246.5mm
Depth4.53", 115.1 mm
Net Weight11.2 lbs, 5.08 kg
Shipping Weight12.7 lbs, 5.76 kgs
Materials of Construction
Coil ConstructionEdge-wound aluminum
Coil FormerPolyimide former
Magnet CompositionFerrite
Core Details
  
Basket MaterialsDie-case aluminum
Cone CompositionPaper
Cone Edge CompositionCloth
Dust Cap CompositionTreated paper
Hide
Footnotes

Multiple units exceed published ratings evaluated under EIA 426A specification while tested in a free-air, non-temperature-controlled environment. Multiple compression drivers exceeded published ratings evaluated under EIA-426A or AES specification while mounted on Eminence’s H290, H290S, or H2EA horn in a non-temperature-controlled environment.

The average output across the usable frequency range when applying 1W/1m into the nominal impedance. i.e: 2.83V/8Ω, 4V/16Ω. Eminence response curves are measured under the following conditions: All speakers are tested at 1W/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25" supplied microphone (software calibrated) mounted 1m from wall/baffle | 2 ft. x 2 ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction | Yamaha P3500S amplifier | 2700 cu. ft. chamber with fiberglass on all six surfaces (three with custom-made wedges). Compression drivers were tested using a 2ft x 2ft baffle built into the wall with horn front mounted.

BETA 8CX, 10CX and 12CX are coaxial speakers with tweeter sold separately. The data for these coaxial woofers was calculated with the ASD:1001 driver screwed into the woofer, but not active.

Prices, specifications and product cosmetics are subject to change without notice.