Pro Audio

Neodymium Series

Get Adobe Reader Cab Design Spec Sheet

KAPPALITE™ 3010HO

Lightweight high power, high output midrange driver. For use in small sealed and vented enclosures.

Suggested Retail  $184.99
Your Price  $179.99

For continental USA shipments only.

  • Free Shipping
  • Free Tech Support
  • 7-Year Warranty*
*Warranty policy may vary outside the USA.
This table charts the specifications for the KAPPALITE™ 3010HO speaker
Speaker Detail
Specification
Nominal Basket Diameter10", 254 mm
Nominal Impedance*8 Ω
Power Rating*
Program Power800 W
Watts400 W
Resonance61 Hz
Usable Frequency Range400 Hz - 4 kHz
Sensitivity*99.9 dB
Magnet Weight11 oz.
Gap Height0.36", 9.3 mm
Voice Coil Diameter3", 76 mm
Thiele & Small Parameters
Resonant Frequency (fs)61 Hz
DC Resistance (Re)5.46 Ω
Coil Inductance (Le)0.57m H
Mechanical Q (Qms)9.93
Electromagnetic Q (Qes)0.27
Total Q (Qts)0.26
Compliance Equivalent Volume (Vas)37.21 liters / 1.31 cu.ft.
Peak Diaphragm Displacement Volume (Vd)162.2 cc
Mechanical Compliance of Suspension (Cms)0.2 mm/N
BL Product (BL)16.27 T-M
Diaphragm Mass Inc. Airload (MMs)34 grams
Efficiency Bandwidth Product (EBP)227
Maximum Linear Excursion (Xmax)4.43 mm
Surface Area of Cone (Sd)366.1 cm2
Maximum Mechanical Limit (Xlim)7.5 mm
Mounting Information
Recommended Enclosure Volume
Sealed 9.91-21.24 liters / 0.35-0.75 cu.ft.
Vented 15.01-28.32 liters / 0.53-1 cu.ft.
Driver Volume Displaced0.037 cu.ft. / 1.04 liters
Major Diameter11.18", 284 mm
Flat to Flat Diameter10", 254 mm
Baffle Hole Diameter9.12", 231.7 mm
Front Sealing GasketYes
Rear Sealing GasketYes
Mounting Holes Diameter0.29", 7.4mm
Mounting Holes B.C.D.10.49", 266.5mm
Depth4.61", 117.1 mm
Net Weight7.1 lbs, 3.22 kg
Shipping Weight8.7 lbs, 3.95 kgs
Materials of Construction
Coil ConstructionEdge wound aluminum voice coil
Coil FormerFiberglass former
Magnet CompositionNeodymium magnet
Core DetailsVented Core
  
Basket MaterialsDie-cast aluminum basket
Cone CompositionTreated paper cone
Cone Edge CompositionSealed cloth Edge
Dust Cap CompositionTreated Paper dust cap
Hide
Footnotes

Multiple units exceed published ratings evaluated under EIA 426A specification while tested in a free-air, non-temperature-controlled environment. Multiple compression drivers exceeded published ratings evaluated under EIA-426A or AES specification while mounted on Eminence’s H290, H290S, or H2EA horn in a non-temperature-controlled environment.

The average output across the usable frequency range when applying 1W/1m into the nominal impedance. i.e: 2.83V/8Ω, 4V/16Ω. Eminence response curves are measured under the following conditions: All speakers are tested at 1W/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25" supplied microphone (software calibrated) mounted 1m from wall/baffle | 2 ft. x 2 ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction | Yamaha P3500S amplifier | 2700 cu. ft. chamber with fiberglass on all six surfaces (three with custom-made wedges). Compression drivers were tested using a 2ft x 2ft baffle built into the wall with horn front mounted.

BETA 8CX, 10CX and 12CX are coaxial speakers with tweeter sold separately. The data for these coaxial woofers was calculated with the ASD:1001 driver screwed into the woofer, but not active.

Prices, specifications and product cosmetics are subject to change without notice.