Pro Audio

Professional Series

Get Adobe Reader Cab Design Spec Sheet

IMPERO™ 15A

High power driver recommended for pro audio in vented enclosures. Suited for two-way top boxes, full-range two-way and three-way boxes, bass guitar boxes, and small subwoofers.

response graph
 
Find a Dealer This table charts the specifications for the IMPERO™ 15A speaker
Speaker Detail
Specification
Nominal Basket Diameter15", 381mm
Nominal Impedance*8 ohms
Power Rating**
Watts1200W
Music Program2400W
Resonance42.97Hz
Usable Frequency Range46Hz - 2kHz
Sensitivity***95.6dB
Magnet Weight109 oz.
Gap Height0.5", 12.7mm
Voice Coil Diameter4", 101.6mm
Thiele & Small Parameters
Resonant Frequency (fs)42.97Hz
DC Resistance (Re)5.42
Coil Inductance (Le)1.47mH
Mechanical Q (Qms)15.33
Electromagnetic Q (Qes)0.4
Total Q (Qts)0.39
Compliance Equivalent Volume (Vas)142.51 liters / 5.03 cu.ft.
Peak Diaphragm Displacement Volume (Vd)625.1cc
Mechanical Compliance of Suspension (Cms)0.14mm/N
BL Product (BL)19.18 T-M
Diaphragm Mass Inc. Airload (MMs)100.57 grams
Efficiency Bandwidth Product (EBP)107.3
Maximum Linear Excursion (Xmax)7.3mm
Surface Area of Cone (Sd)856.3 cm2
Maximum Mechanical Limit (Xlim)15.4mm
Mounting Information
Recommended Enclosure Volume
SealedN/a
Vented53.8-184.0 liters / 1.9-6.5 cu.ft.
Driver Volume Displaced268.4 cu.in. / 4.4 liters
Overall Diameter15.22", 386.59mm
Baffle Hole Diameter13.99", 355.35mm
Front Sealing GasketFitted as Standard
Rear Sealing GasketFitted as Standard
Mounting Holes Diameter0.28", 7.23mm
Mounting Holes B.C.D.14.56", 369.87mm
Depth6.56", 166.62mm
Net Weight24.8 lbs, 11.2 kg
Shipping Weight27.5 lbs, 12.3 kgs
Materials of Construction
Coil ConstructionCopper voice coil
Coil FormerFiberglass former
Magnet CompositionFerrite magnet
Core DetailsBumped Vented Extended core
  
Basket MaterialsDie-cast aluminum basket
Cone CompositionWater resistant paper cone
Cone Edge CompositionTreated cloth cone edge
Dust Cap CompositionWater resistant treated paper dust cap
Hide
Footnotes

* Please consult www.eminence.com for specifications of models with alternative impedances.

** Multiple units exceed published rating evaluated under EIA 426A noise source and test standard while in a free-air, nontemperature-controlled environment.

*** The average output across the usable frequency range when applying 1W/1m into the nominal impedance. ie: 2.83 V /8 ohms, 4 V /16 ohms. Eminence response curves are measured under the following conditions: All speakers are tested at 1W/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25" supplied microphone (software calibrated) mounted 1m from wall/baffle | 2 ft. x 2 ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction | Hafler P1500 Trans-Nova amplifier | 2700 cu. ft. chamber with fiberglass on all six surfaces (three with custom-made wedges).

**** BETA 8CX, 10CX, 12CX and ACOUSTINATOR™ CX 2008 are coaxial speakers with tweeter sold separately. Published Usable Frequency response contingent upon use of APT 50 HF Driver.

***** Multiple units exceeded published rating evaluated under AES 500 and AES 800 noise sources and test standards while mounted on Eminence's TI-2000 horn in a nontemperature-controlled environment.

****** The average on axis output across the entire usable frequency range when applying 1W/1m into the nominal impedance while mounted on a Community SH 494 horn measured with: LMS (software calibrated) using a 0.25" [6.4mm] supplied microphone mounted 1m from horn mouth, Hafler P1500 Trans-Nova amplifier, 2700 cu.ft. chamber w/fiberglass on all six surfaces (three with custom made wedges). Plane-wave tube response and impedance curves measured with LMS on a 0.75" [19.1mm] diameter tube with adapter to allow for smooth transition to throat diameter and 1W/1m into nominal impedance. Prices and Specifications Subject to Change Without Notice.