Pro Audio

Professional Series

Get Adobe Reader Cab Design Spec Sheet


Long throw subwoofer for very small vented boxes. Over-sized top plate and large pole vent help keep the coil cool.

Suggested Retail  $164.99
Your Price  $154.99

For continental USA shipments only.

  • Free Shipping
  • Free Tech Support
  • 7-Year Warranty*
*Warranty policy may vary outside the USA.
This table charts the specifications for the DELTA PRO-18A speaker
Speaker Detail
Nominal Basket Diameter18", 457 mm
Nominal Impedance*8 Ω
Power Rating*
Program Power1000 W
Watts500 W
Resonance28 Hz
Usable Frequency Range37 Hz - 0.2 kHz
Sensitivity*96 dB
Magnet Weight67 oz.
Gap Height0.38", 9.7 mm
Voice Coil Diameter2.5", 64 mm
Thiele & Small Parameters
Resonant Frequency (fs)28 Hz
DC Resistance (Re)5.3 Ω
Coil Inductance (Le)3.43m H
Mechanical Q (Qms)10.38
Electromagnetic Q (Qes)0.33
Total Q (Qts)0.32
Compliance Equivalent Volume (Vas)493.2 liters / 17.42 cu.ft.
Peak Diaphragm Displacement Volume (Vd)796 cc
Mechanical Compliance of Suspension (Cms)0.25 mm/N
BL Product (BL)18.9 T-M
Diaphragm Mass Inc. Airload (MMs)128 grams
Efficiency Bandwidth Product (EBP)84
Maximum Linear Excursion (Xmax)6.7 mm
Surface Area of Cone (Sd)1188 cm2
Maximum Mechanical Limit (Xlim)15 mm
Mounting Information
Recommended Enclosure Volume
Sealed N/a
Vented 85-297 liters / 3-10.5 cu.ft.
Driver Volume Displaced0.212 cu.ft. / 6.01 liters
Overall Diameter18", 457.2 mm
Baffle Hole Diameter16.57", 420.9 mm
Front Sealing GasketYes
Rear Sealing GasketYes
Mounting Holes Diameter0.28", 7.1mm
Mounting Holes B.C.D.17.25", 438.2mm
Depth8.13", 206.5 mm
Net Weight17 lbs, 7.71 kg
Shipping Weight20.5 lbs, 9.3 kgs
Materials of Construction
Coil ConstructionCopper voice coil
Coil FormerPolyimide former
Magnet CompositionFerrite magnet
Core DetailsVented and extended core
Basket MaterialsDie-cast aluminum basket
Cone CompositionPaper cone
Cone Edge CompositionCloth cone edge
Dust Cap CompositionSolid composition paper dust cap

Multiple units exceed published ratings evaluated under EIA 426A specification while tested in a free-air, non-temperature-controlled environment. Multiple compression drivers exceeded published ratings evaluated under EIA-426A or AES specification while mounted on Eminence’s H290, H290S, or H2EA horn in a non-temperature-controlled environment.

The average output across the usable frequency range when applying 1W/1m into the nominal impedance. i.e: 2.83V/8Ω, 4V/16Ω. Eminence response curves are measured under the following conditions: All speakers are tested at 1W/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25" supplied microphone (software calibrated) mounted 1m from wall/baffle | 2 ft. x 2 ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction | Yamaha P3500S amplifier | 2700 cu. ft. chamber with fiberglass on all six surfaces (three with custom-made wedges). Compression drivers were tested using a 2ft x 2ft baffle built into the wall with horn front mounted.

BETA 8CX, 10CX and 12CX are coaxial speakers with tweeter sold separately. The data for these coaxial woofers was calculated with the ASD:1001 driver screwed into the woofer, but not active.

Prices, specifications and product cosmetics are subject to change without notice.