Pro Audio

Professional Series

Get Adobe Reader Cab Design Spec Sheet

DEFINIMAX™ 4012HO

High output, low distortion mid-bass or woofer with a broad frequency response. Recommended for pro audio in both sealed and vented enclosures.

Suggested Retail  $214.99
Your Price  $204.99

For continental USA shipments only.

  • Free Shipping
  • Free Tech Support
  • 7-Year Warranty*
*Warranty policy may vary outside the USA.
This table charts the specifications for the DEFINIMAX™ 4012HO speaker
Speaker Detail
Specification
Nominal Basket Diameter12", 305 mm
Nominal Impedance*8 Ω
Power Rating*
Program Power1200 W
Watts600 W
Resonance51 Hz
Usable Frequency Range48 Hz - 2.7 kHz
Sensitivity*96.2 dB
Magnet Weight109 oz.
Gap Height0.37", 9.5 mm
Voice Coil Diameter4", 102 mm
Thiele & Small Parameters
Resonant Frequency (fs)51 Hz
DC Resistance (Re)5.52 Ω
Coil Inductance (Le)0.95m H
Mechanical Q (Qms)11.03
Electromagnetic Q (Qes)0.36
Total Q (Qts)0.35
Compliance Equivalent Volume (Vas)53.68 liters / 1.9 cu.ft.
Peak Diaphragm Displacement Volume (Vd)338.2 cc
Mechanical Compliance of Suspension (Cms)0.13 mm/N
BL Product (BL)19.56 T-M
Diaphragm Mass Inc. Airload (MMs)78 grams
Efficiency Bandwidth Product (EBP)142
Maximum Linear Excursion (Xmax)6.2 mm
Surface Area of Cone (Sd)545.4 cm2
Maximum Mechanical Limit (Xlim)11.2 mm
Mounting Information
Recommended Enclosure Volume
Sealed 25.49-76.46 liters / 0.9-2.7 cu.ft.
Vented 33.98-99.11 liters / 1.2-3.5 cu.ft.
Driver Volume Displaced0.106 cu.ft. / 3 liters
Overall Diameter12.38", 314.5 mm
Baffle Hole Diameter11.06", 280.9 mm
Front Sealing GasketYes
Rear Sealing GasketYes
Mounting Holes Diameter0.27", 6.9mm
Mounting Holes B.C.D.11.69", 296.9mm
Depth5.32", 135.1 mm
Net Weight22.5 lbs, 10.21 kg
Shipping Weight24.8 lbs, 11.25 kgs
Materials of Construction
Coil ConstructionEdge wound copper voice coil
Coil FormerKapton former
Magnet CompositionFerrite magnet
Core DetailsUndercut with aluminum shorting ring and Core Periphery Ventilation
  
Basket MaterialsDie-cast aluminum basket
Cone CompositionWater resistant paper cone
Cone Edge CompositionCloth cone edge
Dust Cap CompositionWater resistant treated paper dust cap
Hide
Footnotes

Multiple units exceed published ratings evaluated under EIA 426A specification while tested in a free-air, non-temperature-controlled environment. Multiple compression drivers exceeded published ratings evaluated under EIA-426A or AES specification while mounted on Eminence’s H290, H290S, or H2EA horn in a non-temperature-controlled environment.

The average output across the usable frequency range when applying 1W/1m into the nominal impedance. i.e: 2.83V/8Ω, 4V/16Ω. Eminence response curves are measured under the following conditions: All speakers are tested at 1W/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25" supplied microphone (software calibrated) mounted 1m from wall/baffle | 2 ft. x 2 ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction | Yamaha P3500S amplifier | 2700 cu. ft. chamber with fiberglass on all six surfaces (three with custom-made wedges). Compression drivers were tested using a 2ft x 2ft baffle built into the wall with horn front mounted.

BETA 8CX, 10CX and 12CX are coaxial speakers with tweeter sold separately. The data for these coaxial woofers was calculated with the ASD:1001 driver screwed into the woofer, but not active.

Prices, specifications and product cosmetics are subject to change without notice.